Furnace Service and Repair

Call us today if you need service or repair on your heating, cooling, water heating or fireplace systems! CM Heating Comfort Masters is your local answer to staying comfortable all year long.


Furnace Repair in Everett, Washington

Is your heating system not working, or perhaps behaving a little differently? Have you noticed that your home in Everett, WA is not maintaining temperature properly and making funny noises?

If your gas furnace is not working call C.M. Heating now. We fix broken heating equipment all the time in Everett, WA. Or if your system is just getting old, or giving you reasons not to trust it any more let us know. We have many years of experience and we can help you make the right choices when it comes to your furnace system.


CM Heating performed a furnace Diagnostic - Upon investigation, I found that the fan relay has failed. Confirmed proper voltage at disconnect, thermostat and transformer. Did not see 24V across fan relay coil. Replacement is needed

Everett, WA
03-27-2019


CM Heating Perfromed a routine preventive maintenace service on the gas furnace comfort equipment in the home. -Checked and ensure all safety components are within manufacturers requirements and working properly. -Measured -/+ tolerance on consumable components. -Inspect the mechanical and electrical devices/parts within the unit. -Inspect the overall physical and operational condition of the unit. -The unit downstairs is 21 years only and has significant wear on the exchange and flame sensing/pilot assembly components. It’s recommend to replace this unit in the near future. -The attic unit is working properly and all parts are within manufacturers specification. At this time all operations are normal.

Everett, WA
03-28-2019


CM Heating performed a furnace Maintenance - System is running well, all components are within manufacturers specifications. No issues at this time, EAC has been cleaned.

Everett, WA
03-29-2019


CM Heating Changed batteries on thermostat and performed a maintenance service on electric furnace. Cleaned electric filter and found then air cleaning system is no longer working. Recommend the air scrubber to improve indoor air quality. All furnace operations normal at this time.

Everett, WA
03-29-2019


CM Heating Perfromed a routine preventive maintenace service and inspection on the comfort equipment in the home. -Checked and ensure all safety components are within manufacturers requirements and working properly. -Measured -/+ tolerance on consumable components. -Inspected mechanical and electrical devices/parts within the unit. At this time all operations are normal. The following is my recommendations/findings: 1. Flame sensor carbon build up-should be replaced before next winter. 2. Capacitor reaching its maximum tolerance-should be replaced before next winter. 3. Ignitior reaching its life limit-should be replaced. I’ve attached a estimate for the above repairs.

Everett, WA
03-28-2019


CM Heating Perform maintenance on a gas furnace. System operating normally.

Everett, WA
03-14-2019


CM heating performed a furnace diagnostic and found failed blower motor. Customer has no heat and we set up a time for a new unit to be installed.

Everett, WA
03-13-2019


CM Heating Performed a heat pump maintenance operated the system to ensure proper operation, found no issues.

Everett, WA
03-12-2019


CM Heating perform diagnostic on a gas furnace. System was short cycling due to clogged air filter and triggering high limit switch. Install new filter, system operating normally.

Everett, WA
03-19-2019


CM Heating performed a furnace diagnostic and Found extensive repairs needed. Venting is completely corroded. Unit disabled, new unit is needed. Repairs have "totaled" unit

Everett, WA
03-18-2019


CM Heating performed a furnace diagnostic and Found fried contactor. Replaced and unit working properly at this time. Scheduled consult to add heat pump 4/19 @2-4

Everett, WA
04-05-2019


CM Heating Performed a diagnostic service on gas furnace. Found a clogged air pressure port. Unclogged and conducted a check on the general components of the system. There are a couple of components that are showing some wear and getting closer to limit tolerance. Recommend addressing by replacement parts of the igniter source and flame detection device. Currently all operations normal at this time.

Everett, WA
04-09-2019


CM Heating performed a furnace diagnostic and found Furnace door was off kill switch, but after inspecting unit, found failed cap, very dirty blower wheel, and heavily cracked heat exchangers, unit is disabled and from 1993. Replace unit. Consult scheduled 5/9 @4:30-6

Everett, WA
05-06-2019


CM Heating performed a furnace diagnostic and found Igniter failed, order part and return.

Everett, WA
05-06-2019


CM Heating performed a furnace diagnostic and found Bad sequencers. 1 element working currently.

everett, WA
05-01-2019


CM Heating performed a furnace diagnostic and found Igniter failed, order part and return.

Everett, WA
05-06-2019


CM Heating performed a furnace diagnostic and Found a gas leak. Fixed issue. Bubble test to verify no further leak.

Everett, WA
05-06-2019


CM Heating Performed diagnostic on a gas furnace. Upon arrival found the system did not have proper power to the unit. After getting power to unit system started up. Recommended maintenance, and added summer fan switch at the furnace. All system operating normally.

Everett, WA
05-21-2019


CM Heating performed a furnace diagnostic and found Blockage preventing inducer fan from spinning. System started working normally during diagnostic. Furnace has significant dust accumulation and is in need of a maintenance and fan assembly cleaning. Customer indicated the inducer motor was replaced 3 yrs ago. office to call and schedule a maintenance.

Everett, WA
04-15-2019


CM Heating performed a furnace Diagnostic - Upon arrival the furnace was operational but the flame sensor strength was not strong (amber light on control board was flashing). I cleaned sensor and that corrected issue (amber light displaying solid color), I also pulled burner assembly to clean it and vacuumed entire cabinet. I inspected all components which all are in good working order and within manufacturer’s specifications. All operations normal at this time, recommed annual maintenance!

Everett, WA
04-10-2019


CM Heating performed a furnace diagnostic and Found one faulty pressure switch but recommend replacing the secondary as well due to possible defective batch supplied with the furnace. Will order part and return.

Everett, WA
04-15-2019


CM Heating performed a furnace diagnostic and found No heat on arrival. Customer installed new nest thermostat and had wires misplaced. Adjusted the wiring and furnace started running normally. Customer requested new thermostat wire as the original wires were very outdated. Electrician will have to run the wires through the plaster wall. Tstat cannot be mounted properly due to plaster. Re-wires the thermostat and Furnace. Everything is running normally at this time.

Everett, WA
04-15-2019


CM Heating performed a furnace diagnostic and Found a failed igniter, replaced with new. Conducted a free safety check of the overall furnace. The furnace has some consumable components that are below manufacturers specification and should be address to prevent future failure. -Annual preventive maintenance service is recommend for both furnace and air condition units.

Everett, WA
04-18-2019


CM Heating performed a Diagnostic on furnace. Found failed Igniter. Replaced Igniter. Furnace is running at this time. Checked amp draws on motors. Checked heat exchangers per customer request. Recommend replacing equipment due to age.

Everett, WA
05-22-2019